How to carry pump on mountain bike?

How to carry pump on mountain bike

How to carry pump on mountain bike?

Carrying a pump on the mountain bike is always a tricky thing. But if you have the right tools, carrying a pump on a mountain bike becomes easier and you will be able to ride your bike all day without any problems.

How to carry pump on mountain bike? This is a common question among mountain bikers. Here are the most common ways that you can carry your pump while riding your mountain bike.

How to carry pump on mountain bike?

How to carry pump on mountain bike

With your two hands, grip the frame at both ends for a sturdy dragging position.

1 Carry pump with inflating tool and some hose: 

If you have got an inflator in your car or another accessory, then this will be useful, especially when checking puncture repairs in case of flats. There are also pumps that don’t require a battery, so you can use them while riding regardless of the sunshine light situation. 

2 You can also use a handlebar bag: 

This one looks like an entry-level version of the saddle bags. Most good quality pumps have their own handlebar mount that is low profile, making it less visible to thieves. Just make sure to move your gear pod off of it, so they don’t hassle you for being packrat and try not to ride with too much stuff? Also, read about bike frame size measurement.

3 There are special shoes from which you can hold pump just like below: 

So it is totally ok to clutch your bike for pumping then take a nice walk around town, only this time with an additional leg power source! And if you have such shoes but get rid of them midway through ride because of poor fit etc. Keep reading https://pluginid.com/is-it-worth-getting-a-bike-repair-stand/

4 Tango Pumps: 

This pump has two valves. That is, you can fill and also pour the air back out of the tire without stopping for pumping again!

5 Using a dynohub with saddle bag: 

This is useful when you need to carry small things like patches and other tools on the back of your bike. The best part about this kind of setup involves its easy maintenance, comfortability and also keeping heat away from the tires while traveling over long distances in July.

6 This one is a bit different: 

It hides the pump under your seat and at the trunk, thereby making it super-secret. When you lift the backside of the clamp with a flat tire, even someone who doesn’t know that there’s actually no hole in the rear wheel can notice this!

7 Here’s a bunch of inflatable tubes hanging below your seat:

The idea is to pull up shape while you’re riding, exactly like flapping your arms. The air inside will expand the tube, making it lose and deflate, leaving the valve open with a thin piece sticking out of the tire, which can grip on them for pumping and inflating when needed.

8 Here’s another way to fit multiple tubes:

They hide their pump (under the rando car) and crank it with a foot: The tool is mostly hidden as well. Pump repositioning also requires a super low profile – think Vespa scooter without license plate! No honking at other cyclists or worrying that you may run over something while pumping since your head will be on the invisible rear rack of your bike looking straight ahead.

9 One of the most efficient concepts utilizing a flat tire: 

Use it as a seat cushion! You can place your “toy” on the front wheel and ride without worrying about holding or balancing. For example, see how stylish this dog looks riding his youngster with a bike pump in the rear pocket. Pro tip: if you’re using a valve type that looks like the red circle below – don’t forget to provide back up for seating mode.

10 Mounted on the frame! 

Open up frame design allows you comfy standing while riding and enjoying the amazing view. Now all of these cycling modes are possible after we’ve put them in the flat tire!

Attach A Bike Pump To Your Bike

1 First of all – prepare pump, T-bolt (aka cycling valve tool), O ring and seatpost tube or adapter with the tire on it.

2 Without riding the bike, make sure the whole assembly is secure. Try inflating a car tire, so you know how hard to push your parts before using them in real world situations! Note that if you need a special attachment for DIY duct tape will not work: use double sided sticky tape instead of clear tape that allows air to pass through.

3 Install your pump to the valve handle and position it anywhere between the lower bracket and frame/fork.

4 For shorter (single tube) pumps – attach them directly above stem or shock if you have one of those normal looking ones with the horizontal knob.

5 For a longer DIY version, do this first off… Go slow here – make sure all parts are secured before each ride.

6 Thread tube over handle – it should have an angle that fits snugly around your stem and automatically locate the place where the valve will attach. If you do not trust this method, get axle adapter bits from the tubing shop or try other tools offered at Longacre Roadhouse in the riding gear section. You can then screw the tool to either frame or steer with a bar clamp – it all depends on how tight you like pumping. All parts included below are ready for long rides!

7 Now, choose the correct length for tube diameter and thread it through the handle – make sure you can push in all parts around the bike frame to avoid damaging any tubes.

8 Remove rocker protection spring from hardware spindle on the valve – hard wires work best.

9 Attach the valve handle to disk and thread disk between frame and shock if you have one with swing-arm or fork.

10 Insert normal seatpost tube in post area – use O ring as glue here! GO SLOW… your bike needs some cushioning around shocks. Please do not add too much length to these tubes, i.e., front shifters (I know I hate them!). The seat tube lever has a very hard time getting out of limits here if you try to do this before installing a wheel and spokes!

Once all is installed, simply tape in place as always or use glue. After firing up the bike to see how it breathes – pump till the pressure goes down comically low. Look for leaks around the stem rather than valve – clean parts with vinegar sprinkled on your hand and hose/sticky tape where needed. Adjust both bed-levelers.

Conclusion

Pumping is a great way to keep your tires inflated, but it can be tricky to do on the trail. This blog post explains how to carry a pump on your mountain bike and some of the ways you can use it. If you’re looking for more information about how to carry a pump on your mountain bike, please check out our other blog posts about this topic.

No Comments

Sorry, the comment form is closed at this time.